ON 20060501@12:14:45 PM at page:
http://www.piclist.com/io/stepper/linistep/index.htm#38837.7384259259
James Newton[JMN-EFP-786] removed post 38837.7384259259

|Delete '<A TITLE="P-196.40.43.78" NAME="38837.7384259259" HREF="mailto:z4mnT@PgKbI0a.com">z4mnT@PgKbI0a.com</A> &quot;<A NAME="196.40.43.78" HREF="/techref/io/stepper/linistep/ymFilAsm91" TARGET="_top">
/techref/io/stepper/linistep/ymFilAsm91</A> 
NXDLhpt4YsT 1jfWpYjFfiv 0qsDX1UaCzDB&quot;
<!-- 38837.7384259259 EOR -->

  <LI>'



ON 20060501@12:20:59 PM at page:
http://www.piclist.com/io/stepper/linistep/index.htm#38837.8812731481
James Newton[JMN-EFP-786] removed post 38837.8812731481

|Delete '<A TITLE="P-63.201.90.245" NAME="38837.8812731481" HREF="mailto:amr4ts@yahoo.com">amr4ts@yahoo.com</A> asks: <BLOCKQUOTE><A NAME="63.201.90.245">
</A> 
Hi from a retiree who used to tune by watching anodes glow.  <BR>
     I bought three kits instead of four by mistake, so placed an order for the fourth along with a timer module to check out the units with.  The boards seem very well made and organized.  The first went together quite nicely!  I'm looking forward to firing them up!<BR>
     In trying to understand how to set up for &quot;high power half step&quot; mode, I see the word MODE used I think to refer to logic 0 and 1.  Is that correct?  Do I understand correctly, that ctrl pin 6 is wired to 5v supply gnd (-), and 7 to +5?  That there are no current limit resistors other than the 390 ohm ones needed in series on these pins? <BR>
I look forward to your reply!<BR>
Have a good evening,<BR>
Al</BLOCKQUOTE>
<!-- 38837.8812731481 EOR -->

  <LI>'



ON 20060501@3:10:08 PM at page:
http://www.piclist.com/io/stepper/linistep/4axisbuild.htm#38837.3055092593
James Newton[JMN-EFP-786] removed post 38837.3055092593

|Delete '<A TITLE="P-69.146.37.206" NAME="38837.3055092593" HREF="mailto:C-Moore@bresnan.net">C-Moore@bresnan.net</A> asks: <BLOCKQUOTE><A NAME="69.146.37.206">
</A> 
Hi,<BR>
     I really like the kit and concidering buying one to try and then maybe 2 more.I have a question. When using the axis kit what software is suggested to use for communication? Also I have downloaded the hex for the 16F84 and loaded it into the pic.How are the inputs supposed to work? I can toggle RA0 and make PORTB change. What about the other inputs(RA1-4)? Thanks Charlie</BLOCKQUOTE>
<!-- 38837.3055092593 EOR -->
</UL>'



ON 20060529@11:08:52 AM at page:
http://techref.massmind.org/techref/io/stepper/linistep/index.htm#
James Newton[JMN-EFP-786] edited the page. Difference:
http://techref.massmind.org/techref/diff.asp?url=H:\techref\io\stepper\linistep\index.htm&version=53