In SX Microcontrollers, SX/B Compiler and SX-Key Tool, Glenn_Webber wrote:

Hi,
 

I am trying to get a SX28 to talk to a nRF905 [color=#0000ff][color=#0000ff][2]
void[/color][/2][/color][color=#0000ff][color=#0000ff][2]void[/color][/2][/color][color=#008000][color=#008000][2]// Port I/O configuration: 0=output, 1=input
[/color][/2][/color][color=#008000][color=#008000][2]//TX_EN</P>[/color][/2][/color][color=#008000][color=#008000][2]//TRX_CE</P>[/color][/2][/color][color=#008000][color=#008000][2]//PWR_UP</P>[/color][/2][/color][color=#008000][color=#008000][2]//CD</P>[/color][/2][/color][color=#008000][color=#008000][2]//AM</P>[/color][/2][/color][color=#008000][color=#008000][2]//DR</P>[/color][/2][/color][color=#008000][color=#008000][2]//CSN</P>[/color][/2][/color][color=#008000][color=#008000][2]// nRF initial modes</P>[/color][/2][/color][color=#008000][color=#008000][2]// Rx mode</P>[/color][/2][/color][color=#008000][color=#008000][2]// Standby mode</P>[/color][/2][/color][color=#008000][color=#008000][2]// Power down</P>[/color][/2][/color][color=#008000][color=#008000][2]// Chip Select Not = enabled</P>[/color][/2][/color][color=#0000ff][color=#0000ff][2]
void[/color][/2][/color][color=#0000ff][color=#0000ff][2]void[/color][/2][/color][color=#0000ff][color=#0000ff][2]

unsigned[/color][/2][/color][color=#0000ff][color=#0000ff][2]char[/color][/2][/color][color=#0000ff][color=#0000ff][2]unsigned[/color][/2][/color][color=#0000ff][color=#0000ff][2]char[/color][/2][/color][color=#0000ff][color=#0000ff][2]

unsigned[/color][/2][/color][color=#0000ff][color=#0000ff][2]char[/color][/2][/color][color=#0000ff][color=#0000ff][2]

while[/color][/2][/color][color=#0000ff][color=#0000ff][2]

return[/color][/2][/color][color=#0000ff][color=#0000ff][2]

void[/color][/2][/color][color=#0000ff][color=#0000ff][2]void[/color][/2][/color][color=#0000ff][color=#0000ff][2]int[/color][/2][/color][color=#008000][color=#008000][2]//Sets center frequency together with HFREQ_PLL
[/color][/2][/color][color=#008000][color=#008000][2]//Output power, Band 433 or 868/915 MHz</P>[/color][/2][/color][color=#008000][color=#008000][2]//Tx and Rx Address width</P>[/color][/2][/color][color=#008000][color=#008000][2]//RX payload width</P>[/color][/2][/color][color=#008000][color=#008000][2]//Tx payload width</P>[/color][/2][/color][color=#008000][color=#008000][2]//CRC check. Crystal oscillator frequency. </P>[/color][/2][/color][color=#008000][color=#008000][2]//Write nRF configuration</P>[/color][/2][/color][color=#0000ff][color=#0000ff][2]for[/color][/2][/color][color=#008000][color=#008000][2]//Write TX Address</P>[/color][/2][/color][color=#0000ff][color=#0000ff][2]for[/color][/2][/color][color=#0000ff][color=#0000ff][2]
void[/color][/2][/color][color=#0000ff][color=#0000ff][2]char[/color][/2][/color][color=#0000ff][color=#0000ff][2]int[/color][/2][/color][color=#008000][color=#008000][2]//Write TX Payload
[/color][/2][/color][color=#0000ff][color=#0000ff][2]for[/color][/2][/color][color=#008000][color=#008000][2]// Start transmitting</P>[/color][/2][/color][color=#0000ff][color=#0000ff][2]while[/color][/2][/color][color=#008000][color=#008000][2]// Wait for transmission to finish</P>[/color][/2][/color][color=#0000ff][color=#0000ff][2]
void[/color][/2][/color][color=#0000ff][color=#0000ff][2]void[/color][/2][/color][color=#0000ff][color=#0000ff][2]int[/color][/2][/color][color=#0000ff][color=#0000ff][2]char[/color][/2][/color][color=#008000][color=#008000][2]//Read RX Payload
[/color][/2][/color][color=#0000ff][color=#0000ff][2]for[/color][/2][/color][color=#0000ff][color=#0000ff][2]if[/color][/2][/color][color=#800000][color=#800000][2]'o'[/color][/2][/color][color=#800000][color=#800000][2]'n'[/color][/2][/color][color=#0000ff][color=#0000ff][2]else[/color][/2][/color][color=#0000ff][color=#0000ff][2]if[/color][/2][/color][color=#800000][color=#800000][2]'o'[/color][/2][/color][color=#800000][color=#800000][2]'f'[/color][/2][/color][color=#800000][color=#800000][2]'f'[/color][/2][/color][color=#0000ff][color=#0000ff][2]else[/color][/2][/color][2] USBsend(SpiRxBuf);</P>
}

 

I have tryed the Shiftout and Shiftin but have had no luck, I need a SPI.

Thanks

Glenn
[/2]
</FONT></FONT>

---------- End of Message ----------


You can view the post on-line at:
http://forums.parallax.com/forums/default.aspx?f=7&p=1&m=355205

Need assistance? Send an email to the Forum Administrator at forumadmin@parallax.com

The Parallax Forums are powered by dotNetBB Forums, copyright 2002-2009 (http://www.dotNetBB.com)