PAUL James wrote:
> Michael,
> 
> No, because the firmware file I am attempting to program is the file we
> read from the unit.
> We just went in and modified a few bytes to patch a particular portion
> of the program.  But 
> The patch we made was at the beginning of the file, not anywhere near
> the end of the file which
> Goes up to $4015.   It seems to me that this address just about has to
> be some processor specific
> Setup information location, and not a program space location.  Something
> like maybe the CONFIG ...

Well, if it *is*, it should be clear from the data sheet.
The CONFIG addresses are as fare as I know always documented.

[Downloading datashet...]
Yup, CONFIG bits are between h'2000' and h'2007', which
probably are adressed as h'4000' to h'4015' in the HEX file...

Jan-Erik.

> Register or maybe the OSCILLATOR control register or some such.  At
> least that's my guess.
> 
> Thanks for the repsonse, and if you have any futher ideas or
> suggestions, please pass them along.
> I'll take all the help I can get.
> 
> 
> 	
> Thanks and Regards,
> 
> 	
> Jim  
> 
> 
> 
> -----Original Message-----
> From: piclist-bounces@mit.edu [mailto:piclist-bounces@mit.edu] On Behalf
> Of Michael Rigby-Jones
> Sent: Friday, May 09, 2008 10:49 AM
> To: Microcontroller discussion list - Public.
> Subject: RE: [PIC]: Memory Map Question
> 
> 
> 
>> -----Original Message-----
>> From: piclist-bounces@mit.edu [mailto:piclist-bounces@mit.edu] On
> Behalf
>> Of PAUL James
>> Sent: 09 May 2008 16:34
>> To: Microcontroller discussion list - Public.
>> Subject: [PIC]: Memory Map Question
>>
>> All,
>>
>> I have a question for the PIC community that has me stumped at the 
>> moment.  Here is the scenario.
>> I am using an ispPro programmer from Basic Micro.  It works well, and
> we
>> have used it for a long time.
>> We have a 16F76 in one of our systems.  I erased the program memory,
> and
>> reprogrammed it with different code.
>> At the end of the programming cycle, I get an error that the
> programmer
>> can't verify location $4000.
>> The top of the address space is $3FFF or at least I thought it was.  I
> 
>> looked at the datasheet, but didn't find anything about address $4000.
> 
>> I thought it might be a system location that is only availabe to the 
>> device programmer at program time.
>>
>> Does anybody know what is significant about this location?  When I do
> a
>> read, I see location $4000 is $80.  When I erase it, it still says
> $80.
>> It should be $FF if it is truly erased I think.  If I reprogram it
> with
>> the old firmware, I still get the error.  It's like the bit is stuck 
>> high.  It can't be programmed low.
>>
>> Anyway, if anyone has any insight, let me know.   I would appreciate
> it.
> 
> Is it possible your hex file contains addresses past the end of the
> PIC's memory, and the programmer is blindly attempting to program them?
> 
> Mike
> 
> =======================================================================
> This e-mail is intended for the person it is addressed to only. The
> information contained in it may be confidential and/or protected by law.
> If you are not the intended recipient of this message, you must not make
> any use of this information, or copy or show it to any person. Please
> contact us immediately to tell us that you have received this e-mail,
> and return the original to us. Any use, forwarding, printing or copying
> of this message is strictly prohibited.
> No part of this message can be considered a request for goods or
> services.
> =======================================================================
> 
> --
> http://www.piclist.com PIC/SX FAQ & list archive View/change your
> membership options at http://mailman.mit.edu/mailman/listinfo/piclist
> 
-- 
http://www.piclist.com PIC/SX FAQ & list archive
View/change your membership options at
http://mailman.mit.edu/mailman/listinfo/piclist