Okay, this may NOT be the friendliest documentation.
ICD2 comes with a QUICKSHEET. A very big one. It tells
the user how to wire the PIC and ICD2 together. The
RJ12 connection is used. 5pins are needed. Please LOOK
at the quicksheet to determine which line goes where.
I used a wire wrap to my PIC 16F873A. No problems.
Again have the pic12f675 datasheet in front of you
when you plug it in. HAVE the DMM to measure the
voltage of the pins. MPLAB has 2 settings for the ICD2
one as a programmer and one as a debugger. For
convinence use the programmer first. AND for the first
try, power the ICD2 using a 9VDC adapter. Check the
polarity when you plug power into the ICD2. Then wire
the ICD2 to the PIC. For starters the PIC should be
isolated from the current circuit. 

Use MPLAB to connect to the PIC using the ICD2 as a
programmer.*Under the programmer menu*.

Regards,
John

--- Shawn Wilton <black9@gmail.com> wrote:

> OK, my ICD has arrived, and I'm trying to figure out
> how to hook the darn
> thing up.  I can't find the docs needed to hook the
> ICD header for the
> pic12f675 to my application.
> 
> Nor can I figure out how to program my application. 
> I found some app notes
> that say you can't program when using the header,
> but you need the header to
> debug.  So since I program my application through a
> custom firewire cable, I
> suppose I will need two interface cables?  One for
> debug, and another for
> programming since one will have to use the header
> and the other will not?
> 
> Am I correct in my assertions?
> 
> 
> 
> On 9/20/06, John Chung <kravnus@yahoo.com> wrote:
> >
> > Thanks for the info
> >
> > John
> >
> > --- WH Tan <whsiung.my@gmail.com> wrote:
> >
> > > 2006/9/20, John Chung wrote:
> > >
> > > >   Calibration data? Not sure what is that and
> > > ICD2...
> > >
> > > There are 2 kinds of calibration data in
> PIC12F675.
> > > All are
> > > preprogrammed in factory.
> > >
> > > 1) Bandgap (2 bit) located in configuration
> > > register.
> > >
> > > 2) OSCCAL value located at last ROM address
> (0x3FF),
> > > in the form of
> > > RETLW XX, where XX is the calibration value for
> the
> > > internal
> > > oscillator.
> > >
> > >
> > > Best regards,
> > >
> > > --
> > > WH Tan
> > > --
> > > http://www.piclist.com PIC/SX FAQ & list archive
> > > View/change your membership options at
> > > http://mailman.mit.edu/mailman/listinfo/piclist
> > >
> >
> >
> > __________________________________________________
> > Do You Yahoo!?
> > Tired of spam?  Yahoo! Mail has the best spam
> protection around
> > http://mail.yahoo.com
> > --
> > http://www.piclist.com PIC/SX FAQ & list archive
> > View/change your membership options at
> > http://mailman.mit.edu/mailman/listinfo/piclist
> >
> 
> 
> 
> -- 
> 
> Shawn Wilton (b9 Systems)
> http://b9Systems.com  <- New web page
> -- 
> http://www.piclist.com PIC/SX FAQ & list archive
> View/change your membership options at
> http://mailman.mit.edu/mailman/listinfo/piclist
> 


__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around 
http://mail.yahoo.com 
-- 
http://www.piclist.com PIC/SX FAQ & list archive
View/change your membership options at
http://mailman.mit.edu/mailman/listinfo/piclist