Typo copied and bastardised should be movwf..
Are you in the correct bank??

Steve

-----Original Message-----
From: piclist-bounces@mit.edu [mailto:piclist-bounces@mit.edu] On Behalf Of
Bob Axtell
Sent: 18 April 2006 18:26
To: Microcontroller discussion list - Public.
Subject: Re: [PIC] PIC16F877A PortD ?

Do I need a movfw TRISD ? I have a MOVWF TRISD, course it isn't working..
- - -

BTW, ICD2 is showing TRISD as having a value of 00, whereas I loaded it 
with 0F.. go figure.
LOOKS like I am overwriting it someplace.

--Bob

Steve Smith wrote:
> This setup uses portd as a bi-directional 8 bit bus check it against your
> initialisation I know it works (in my app)the A-D is set for part and part
> but port D is all digital
>
> Rgds
> Steve
> ;----------------------- INITALISATION
> ROUTIENE-------------------------------
> 	bcf		STATUS,RP0		; first do page 0 stuff.
> yep, page 0
> 	Gie_off							; turn off
> int and test its off
> 	clrf		STATUS		; force bank zero
> 	clrf		INTCON		; disable ints ect
> 	clrf		PIR1			; clear all flag bits
> PORT_SETUP
>  	clrf		PORTA
> 	clrf		PORTB 
> 	movlw		b'00100000'		; OE off on outputs
>
> 	movwf		PORTC
> 	clrf		PORTD
> 	clrf		PORTE		
> 	BANK1
> 	movlw		b'00111111'		; IO for port
> 	movwf		TRISA
> 	movlw		b'11111111'
> 	movwf		TRISB
> 	movlw		b'11011000'
> 	movwf		TRISC
> 	movlw		b'11111111'
> 	movfw		TRISD
> 	clrf		TRISE			
> WDT_SETUP
> 	movlw   	B'00001111'     	; SET WDT TIMER TIMEOUT
> PULLUP Off
> 	movwf   	OPTION_REG      
> ADCON_SETUP
> 	movlw		B'11000011'		; LITERAL FOR ADCON1 
>       movwf		ADCON1          	; LOAD ADCON1
> INT_SETUP
> 	movlw		B'01000001'		; SET UP TMR1 FOR OVERFLOW
> and ADIE
> 	movwf		PIE1
>     BANK0		        		; RETURN TO BANK_0 
> 	movlw   	B'11000000'    	; INTERRUPT CONTROL ENABLE GIE AND
> PIE1
> 	movwf		INTCON		; ENABLE INT'S
>
>
> -----Original Message-----
> From: piclist-bounces@mit.edu [mailto:piclist-bounces@mit.edu] On Behalf
Of
> Mike Hord
> Sent: 18 April 2006 17:30
> To: Microcontroller discussion list - Public.
> Subject: Re: [PIC] PIC16F877A PortD ?
>
> Are there analog input options on those pins?  I think I
> remember some parts having analog on PORTD, but that
> could just be my imagination...
>
> Mike H.
>
> On 4/18/06, Bob Axtell <engineer@cotse.net> wrote:
>   
>> This is embarassing. I have used this part in the past and
>> never had a problem with portD, but I have 4 PCBs showing
>> that PortD, with pins set as inputs, never seems to pass data
>> into w. I know that portD uses the "Parallel Port" feature, but
>> I think I have turned it off.
>>
>> I guess I am missing something. . Any ideas?
>>
>> --Bob
>> --
>> http://www.piclist.com PIC/SX FAQ & list archive
>> View/change your membership options at
>> http://mailman.mit.edu/mailman/listinfo/piclist
>>
>>     
>
>   

-- 
http://www.piclist.com PIC/SX FAQ & list archive
View/change your membership options at
http://mailman.mit.edu/mailman/listinfo/piclist


-- 
http://www.piclist.com PIC/SX FAQ & list archive
View/change your membership options at
http://mailman.mit.edu/mailman/listinfo/piclist