There has been considerable discussion in the past about pruning the excess
verbage from responses. The consensus at that time seemed to be that less is
best.

I bet this thread took a bad turn do to finals week or other frustrating
deadlines. I read the whole thread and cannot find any real reason to take
offense without an external trigger.

Take a break, get some rest and get back on the team. We need you all...

BTW, no pruning this time and the website means what you see is what you
get?

John Ferrell
http://DixieNC.US

----- Original Message -----
From: "Shawn Wilton" <shawn@BLACK9.NET>
To: <PICLIST@MITVMA.MIT.EDU>
Sent: Sunday, May 09, 2004 3:13 AM
Subject: Re: [OT:] "splitting" a serial signal


> Um, ok.  What the hell?  I know what I posted, but I sent out another
> post replacing the typo "my" with simply rs232 drivers.  Perhaps you/he
> should have read that email as well, especially before criticizing and
> replying with this:
>
>  >Slow down.....Read the posts.......... Understand .....Then reply,
>  >If, and only if you have anything constructive to say?
>
> I never mentioned that there was anything on my site, nor did I post a
> link outside of what's in my typical signature.  If you're going to
> mindlessly criticize my reply, perhaps you should do the same of his
> question.
>
> What am I supposed to say to someone that simply says, Hey, all I get is
> your web page at your site, what am I doing wrong?  Had he inlined the
> original message, then at least I would have realized that he didn't get
> the previous correction, otherwise, I have no idea what he's asking.
>
> FWIW:  My suggestion was to take as many RS232 drivers (max232/233) as
> you have external "remotes", tie the outputs to the "remotes" and all
> the inputs to the single pic driving the whole lot.  If you do this,
> then you should have enough signal coming from the pic to drive the
> input side of the drivers (good old ttl) and the drivers should have
> enough power to run all the remotes.
>
> Think of it like this:
>
> A, B, C, D = rs232 drivers (max232/233)
>
>            PIC                  (master pic)
>             |
> --------------------------
>   |     |       |       |       (input side)
>   A     B       C       D       (driver chips)
>   |     |       |       |       (output side)
> remote1 remote2 remote3 remote4
>
> Does that make sense?  Basically what you're attempting to do, is
> cascase the load so that it's evenly distributed.  You may also want to
> consider such things as how many loads you wish to ultimately drive, as
> well as the amount of power each individual driver can sink.  If the
> cost of components is an issue, then you may not want to use a single
> driver per remote.  But that will ultimately be determined by the amount
> of current the drivers can sink, and the amount drawn by the load.
>
> With luck that ascii art won't get scrambled.
>
>
>
> Shawn Wilton
> Junior in CpE
> MicroBiologist
>
> Phone: (503) 881-2707
> Email: shawn@black9.net
>
> http://black9.net
>
> p.cousens wrote:
> > This is driving me crazy, quantity of posts is no substitute for quality
> > Slow down.....Read the posts.......... Understand .....Then reply,
> > If, and only if you have anything constructive to say
> >
> > Shawn you are very close to being filtered from my PICLIST
> > Try harder remember you last post and maybe you will understand the
> > context of the replies
> >
> > Peter Cousens
> >
> > -----------------------------------------------
> >
> > Shawn Wilton Wrote
> >
> > Darren, use my rs232 drivers.  You can hook up the input sides of the
> > drivers to your single driving PIC, and the output sides to all the
> > other "remotes".
> >
> >
> > Shawn Wilton
> > Junior in CpE
> > MicroBiologist
> >
> > Phone: (503) 881-2707
> > Email: shawn@black9.net
> >
> > http://black9.net
> >
> > ---------------------------------------------------
> > Redtock8 wrote
> >
> > Shawn,
> > All I get at Black9.net is a black circle with horns.
> > What am I doing wrong?
> >
> > -------------------------------------------
> >
> > Shawn Wilton Wrote
> >
> > Nothing, why?
> >
> >
> > Shawn Wilton
> > Junior in CpE
> > MicroBiologist
> >
> > --
> > http://www.piclist.com#nomail Going offline? Don't AutoReply us!
> > email listserv@mitvma.mit.edu with SET PICList DIGEST in the body
>
> --
> http://www.piclist.com#nomail Going offline? Don't AutoReply us!
> email listserv@mitvma.mit.edu with SET PICList DIGEST in the body

--
http://www.piclist.com#nomail Going offline? Don't AutoReply us!
email listserv@mitvma.mit.edu with SET PICList DIGEST in the body