(typo)
 According to the Microchip line card I have (2nd half '03), you are
 correct, the 628A does not list ICD among the features. Good catch, Bob.

 -Denny

>>
> > Hmmm. I didn't know that the 628A could be debugged with the ICD2; it
> > can be programmed, but NOT debugged. It simply doesn't have the
internal
> > debugging hardware.
> >
> > Can somebody verify this?
> >
> > --Bob
> > Tom wrote:
> > > I can second Dan's suggestion, Harold.  The ICD-2 error messages are
> > > cryptic at best and wrong at worst.
> > >
> > > Although I have not yet tried a '628A device, I did have a problem
once
> > > when trying to work with an 18F452 in a PICDEM2 PLUS board in which
the
> > > oscillator was not functioning.
> > >
> > > Hoping you get it fixed before the end of the year,
> > > Tom Fool
> > >
> > > At 03:26 PM 12/31/2003 -0800, you wrote:
> > >
> > >>Check the crystal type....I've gotten that error before when it's
> > >>incorrect.  Also check the proper device is selected as well.
> > >>
> > >>Both of these have caused me a few moments of serious soul searching
> > >>when connecting a new project and not getting a response.
> > >>
> > >>DD
> > >>
> > >>On Wed, 2003-12-31 at 15:06, Harold Hallikainen wrote:
> > >>
> > >>> I am having a problem with the ICD-2 and a 16F628A. I've tried two
> > >
> > >
> > > --
> > > http://www.piclist.com#nomail Going offline? Don't AutoReply us!
> > > email listserv@mitvma.mit.edu with SET PICList DIGEST in the body
> > >
> >
> >
> >
> > Tom wrote:
> > > I can second Dan's suggestion, Harold.  The ICD-2 error messages are
> > > cryptic at best and wrong at worst.
> > >
> > > Although I have not yet tried a '628A device, I did have a problem
once
> > > when trying to work with an 18F452 in a PICDEM2 PLUS board in which
the
> > > oscillator was not functioning.
> > >
> > > Hoping you get it fixed before the end of the year,
> > > Tom Fool
> > >
> > > At 03:26 PM 12/31/2003 -0800, you wrote:
> > >
> > >>Check the crystal type....I've gotten that error before when it's
> > >>incorrect.  Also check the proper device is selected as well.
> > >>
> > >>Both of these have caused me a few moments of serious soul searching
> > >>when connecting a new project and not getting a response.
> > >>
> > >>DD
> > >>
> > >>On Wed, 2003-12-31 at 15:06, Harold Hallikainen wrote:
> > >>
> > >>> I am having a problem with the ICD-2 and a 16F628A. I've tried two
> > >
> > >
> > > --
> > > http://www.piclist.com#nomail Going offline? Don't AutoReply us!
> > > email listserv@mitvma.mit.edu with SET PICList DIGEST in the body
> > >
> >
> > --
> > http://www.piclist.com#nomail Going offline? Don't AutoReply us!
> > email listserv@mitvma.mit.edu with SET PICList DIGEST in the body
>
> --
> http://www.piclist.com#nomail Going offline? Don't AutoReply us!
> email listserv@mitvma.mit.edu with SET PICList DIGEST in the body

--
http://www.piclist.com#nomail Going offline? Don't AutoReply us!
email listserv@mitvma.mit.edu with SET PICList DIGEST in the body