In an effort to eliminate unsolicited e-mail, I have installed =
SpamEnder.  You must REPLY to this e-mail, without modifying the subject =
line, so that SpamEnder will release your original message to my Inbox. =
Upon my approval, future e-mails you send to me will be released =
automatically. If you do not REPLY to this e-mail, SpamEnder will block =
all future e-mails from this address and will not give you another =
opportunity to reply.
=0A=
----------------------------------------------------------=0A=
SpamEnder stops 100% of all SPAM e-mail and NEVER blocks the e-mail you =
wish to receive.  It even comes with a Money Back Guarantee.  For more =
information about SpamEnder, open your browser to =
http://www.spamender.com/=0A=
----------------------------------------------------------=0A=
Copyright 2003, Evolvian, Inc.=0A=
=0A=
Excerpt from original message:
Robert,

First, a major no-no ... although your method of coding could work, you =
should=20
really, really, really (insert infinite loop here :-) use the =
definitions=20
from the .inc files already created by Microchip.  They're part of the =
MPLAB=20
package.  Otherwise, the code is difficult to read, and adds major =
sources of=20
errors.  Especially if, as you say, you're a programmer. :-)

That said, assuming your code compiles okay and does have the correct =
register=20
addresses, if the switch were in it's unpressed state, RA1 would be "1". =
 The=20
code would loop at BEGIN and the line after that (goto BEGIN).  Now, if =
the=20
switch were pressed, RA0 goes to "0", so the code sets PORTB to all =
"1"'s=20
which would turn on the LED, BUT...assuming the switch "bounces", as is=20
expected, RA1 would flicker between "1" and "0" for a short time.  But =
long=20
enough that as it gets to KEEPON, RA1 could be at 0 and would not loop =
at=20
KEEPON.  It would go straight to clearing portB and exit.  It could also =
loop=20
at KEEPON a few times before exiting due to the same switch bounce =
problem. =20
A few times is very fast, since the internal oscillator is 4Mhz, so you =
would=20
not even see the LED come on.

Quick test... try a really large capacitor at the input to RA1 (Cap +ve =
to=20
RA1, cap -ve to gnd).  If that solves your problem then you know it's =
the=20
bounce issue.

Cheers,
-Neil




On Tuesday 10 June 2003 19:47, rrc124+@PITT.EDU scribbled:
> I can't get my inputs to work. I am using a pull up switch, have set =
all
> pins but 1 to outputs, then tied them to ground. I am using a =
PIC16F628
> with the configs set to everything off/disabled except the power up =
timer.
> I have selected the internal oscillator. I'm a programmer..not EE, so
> that's my weak point but i have been checking the circuit for 3 days =
and
> can't find what's wrong. The chip works because i got one of those LED
> blinking things to work fine. Guys...thank you so much...it's very
> upsetting when you're just starting out and can't get the easiest =
thing to
> work. The only odd thing i could find was that my programming software
> (WinPicProg, from Dontronics) generates a different config word then =
does
> MPLAB with the same settings.
>
> Here is my code:
>
> TMR0            EQU             1
> OPTION_R        EQU             1
> PORTA           EQU             5
> PORTB           EQU             6
> TRISA           EQU             5
> TRISB           EQU             6
> STATUS          EQU             3
> ZEROBIT         EQU             2
> CARRY           EQU             0
> PCON            EQU             0EH
> COUNT           EQU             20H
>
>                         LIST P=3D16F628                                =
     =20
>           ;  tells which processor is use ;MPLAB generated        =
__CONFIG
> 0x3F10
>                         __CONFIG 0x3D10  ;WinPicProg generated
>
>                         org             0
>                         goto    START
>
> ; config section
>
> START                   bsf     STATUS, 5
>                         movlw   b'11111111'
>                         movwf   TRISA
>                         movlw   b'00000000'
>                         movwf   TRISB
>
>                         movlw   b'00000100'
>                         movwf   OPTION_R
>                         clrf    PCON
>
>                         bcf     STATUS, 5
>                         clrf    PORTA
>                         clrf    PORTB
>
> ; program starts now
>
> BEGIN           btfsc   PORTA, 1
>                         goto    BEGIN
>                         movlw   b'11111111'
>                         movwf   PORTB
> KEEPON          btfss   PORTA, 1
>                         goto    KEEPON
>                         clrf    PORTB
>                         goto    BEGIN
>
>                         END
>
> Here is my circuit:
>                                    GND
>
> [9V+ Battery]--[914 diode]--[7805 Volt Reg]--+
>
>                           +-----[10k Res]----+
>
>             A1/PIN 18-----+--[switch]--GND   |
>
>            Vdd/PIN 14------------------------+
>
>            Vss/PIN 05------------------------GND
>
>             B4/PIN 10--[470 Ohm Res]--[LED]--GND
>
>             B3/PIN 09--[470 Ohm Res]--[LED]--GND
>
> All other pins set as output, tied to ground. The switch part of the
> circuit allows 4.5V to A1 and when pressed drops the voltage down to =
0. I
> checked with my multimeter. Thank you so much everyone.
>
> E-Mail: rrc124@pitt.edu
>
> Robert Campbell

--
http://www.piclist.com hint: To leave the PICList
mailto:piclist-unsubscribe-request@mitvma.mit.edu


--
http://www.piclist.com hint: To leave the PICList
mailto:piclist-unsubscribe-request@mitvma.mit.edu