Hi-
Try my Swiki page at:  http://eagletips.swiki.net/1
Also go to the USA website and download the maual.  The built-in HELP is usually
quite useful too.
David

Tal Bejerano - AMC wrote:

> 10x 4 help guys! it really help me!
> where all of u got the manuals? i can't find any....:-(
>
> Regards
>
> Tal Bejerano
> AMC - ISRAEL
>
> -----Original Message-----
> From: pic microcontroller discussion list [mailto:PICLIST@MITVMA.MIT.EDU]On
> Behalf Of Stefano
> Sent: Sunday, May 12, 2002 4:37 AM
> To: PICLIST@MITVMA.MIT.EDU
> Subject: Re: [PIC]: Eagle Auto route
>
> before reducing the dimension of the traces, you might try to change the
> directional organization of the routing. There are two menus (left up)
> with TOP and BOTTOM preferred direction. CHoose the star * and see how
> much it helps. Then start decreasing the number 50. Go to 30, 20 and below
> in steps of one... DO not choose a parameter too small (5 or 8) otherwise
> traces are too thin and close each other.
>
> Stefano Curtarolo
>
> > Use the Group tool to select all the traces in the board view, then  use
> the
> > Ripup tool, but RIGHT click the board, all the traces should revert to
> > air-wires.  Also reroute with the Routing Grid set to 10 (I think the
> default is
> > 50, and that is usually too big).
> > David
> >
> > Tal Bejerano - AMC wrote:
> >
> > > Hi All
> > >
> > > ok.. I have a complex schematic and I want to do auto route.
> > > I start the auto route and the process begin
> > > the final result are too many unrouted tracks..
> > > my question is:
> > > how I start a new auto route? playing with options/parameters don't give
> any
> > > better results
> > > deleting the board and start new board auto route force me to place the
> > > component in place again.
> > > what  can I do to start auto route without all this mess?
> > > what are the differences in the direction signs? "/ \ * . |"
> > > if someone can explain in details I'll appreciate it.
> > >
> > > Regards
> > >
> > > Tal Bejerano
> > > AMC - ISRAEL
> > >
> > > --
> > > http://www.piclist.com hint: To leave the PICList
> > > mailto:piclist-unsubscribe-request@mitvma.mit.edu
> >
> > --
> > http://www.piclist.com hint: To leave the PICList
> > mailto:piclist-unsubscribe-request@mitvma.mit.edu
> >
> >
>
> --
> http://www.piclist.com hint: To leave the PICList
> mailto:piclist-unsubscribe-request@mitvma.mit.edu
>
> --
> http://www.piclist.com hint: PICList Posts must start with ONE topic:
> [PIC]:,[SX]:,[AVR]: ->uP ONLY! [EE]:,[OT]: ->Other [BUY]:,[AD]: ->Ads

--
David Harris
  OmniPort Home Page:  http://www3.telus.net/OmniPort1/
    Discussion egroup: http://groups.yahoo.com/group/OmniPort
    Swiki:  http://omniport.swiki.net/1

--
http://www.piclist.com hint: PICList Posts must start with ONE topic:
[PIC]:,[SX]:,[AVR]: ->uP ONLY! [EE]:,[OT]: ->Other [BUY]:,[AD]: ->Ads