Hi, if you are absolutely sure the wires are not reversed, the there is only one question: to which pin of the paralel port you did connect the GND lead of the DVM? Regards, Imre +-----------------------------------------------------------------------+ | The information transmitted is intended only for the person or entity | | to which it is addressed and may contain confidential and/or | | privileged material. Any review, retransmission, dissemination or | | other use of, or taking of any action in reliance upon, this | | information by persons or entities other than the intended recipient | | is prohibited. If you received this in error, please contact the | | sender and delete the material from any computer. | +-----------------------------------------------------------------------+ On Wed, 15 Aug 2001, Alaa El-agha wrote: > Some further insight: > > Actually the pport responds to the DEBUG commands and sets the levels > accordingly. However, I measured the voltage levels with a DVM and found > that high or 1 is aroung -5V and low or 0 is around 0V. > > My understanding is that the pport is TTL. It is measuring a significant > negative level (the DVM leads are not reversed, to make sure I am in the > right directioin, connected a diode LED). > > Am I missing something here, or my port is malfunctioning. If so, how the > brother printer worked well? > > Regards, > Alaa > ----- Original Message ----- > From: "Alaa El-agha" > To: > Sent: Wednesday, August 15, 2001 1:34 AM > Subject: Re: [PIC]: Can't get the programmer to work > > > > Hi Imre, > > > > Thanx for the feedback. The wiring of my kit is actually different from > the > > default settings in the s/w. However, I changed the settings to indicate > the > > right Data In, Data Out, Clk etc. > > > > I did re-wire the circuit and go thru the verification steps. everything > is > > ok, except whten I connect the parallel port, when pin 5 (Vpp) goes low. > It > > does not change regardless what the s/w is set to. > > > > Thru DEBUG, the parallel port base addr is 0378. I sent all 1's to the > port, > > but it measures low. This makes me suspicious about my parallel port. > > However, I had a brother laser printer two weeks ago and it worked fine. > > > > Any suggestions? > > > > Kevin, > > I actually blow my transistor too. > > > > Thanx > > Alaa > > ----- Original Message ----- > > From: "dr. Imre Bartfai" > > To: > > Sent: Tuesday, August 14, 2001 4:16 AM > > Subject: Re: [PIC]: Can't get the programmer to work > > > > > > > Hi, > > > > > > I have a true programmer from Dobaj so I do not know the differences, > but > > > in my version the output pins can be configured. Per default, the D2 pin > > > is the MCLR control so you should check, and if do not match, then > either > > > reconfigure the software, or - if it is not possible - then re-wire the > > > h/w. > > > > > > BTW u can test the port with debug in dos, using the 'o' command. > > > I hope this helps. > > > > > > Regards, > > > Imre > > > > > > > > > > +-----------------------------------------------------------------------+ > > > | The information transmitted is intended only for the person or entity > | > > > | to which it is addressed and may contain confidential and/or > | > > > | privileged material. Any review, retransmission, dissemination or > | > > > | other use of, or taking of any action in reliance upon, this > | > > > | information by persons or entities other than the intended recipient > | > > > | is prohibited. If you received this in error, please contact the > | > > > | sender and delete the material from any computer. > | > > > > +-----------------------------------------------------------------------+ > > > > > > On Mon, 13 Aug 2001, Alaa El-agha wrote: > > > > > > > Hi everyone, > > > > > > > > I am new to PIC. I have the Parallel programmer assembled (from P. > > Andesren at http://www.phanderson.com/PIC/picstart.html ) and got Bojan's > > P16prol for 16F84. However, I did not get the programmer to work. > > > > > > > > I am sure that the circuit is wired correctly, and the s/w settings > are > > ok. What I noticed is the that D3 (pin 5) on the parallel port is always > > low, which makes the 13.4V voltage appear all the time on /MCLR, hence > > preventing correct setup. > > > > > > > > I am runing Windows98. I tried running from DOS, but also got he same > > problem. > > > > > > > > Any suggestion, help is appreciated. > > > > > > > > REgards, > > > > Alaa > > > > > > > > -- > > > > http://www.piclist.com#nomail Going offline? Don't AutoReply us! > > > > email listserv@mitvma.mit.edu with SET PICList DIGEST in the body > > > > > > > > > > > > > > > > > > -- > > > http://www.piclist.com hint: To leave the PICList > > > mailto:piclist-unsubscribe-request@mitvma.mit.edu > > > > > > > > > > > > > -- > > http://www.piclist.com hint: PICList Posts must start with ONE topic: > > [PIC]:,[SX]:,[AVR]: ->uP ONLY! [EE]:,[OT]: ->Other [BUY]:,[AD]: ->Ads > > > > > > -- > http://www.piclist.com hint: PICList Posts must start with ONE topic: > [PIC]:,[SX]:,[AVR]: ->uP ONLY! [EE]:,[OT]: ->Other [BUY]:,[AD]: ->Ads > > > -- http://www.piclist.com hint: The list server can filter out subtopics (like ads or off topics) for you. See http://www.piclist.com/#topics