On Sun, 10 Jan 1999 16:04:32 +1100 David Lions writes: >Hi, > >My parents have an old TV in their bedroom without a remote control. >I >would like to add the functionality of a VCR, but without the tape >deck >part. It is easy to find a junker VCR which still tunes OK but has no hope of ever playing a tape again. This would serve the remote-control tuning part of the project. (You also get a clock for free, if you can figure out how to set it...) For the power on/off, most VCRs have a 12V DC supply bus which switches on and off with the "Power" button. Connect the coil of a relay to this bus and the contacts in series with the AC line to the TV. Usually you'll find the switched supply near the motor driver section. Obligatory safety note: Unlike a TV, it's fairly safe to probe around inside a VCR since most everything works on low voltages that are isolated from the power line. But stay away from areas near where the power cord connects, since there may be line voltage there. It's best to treat everything as being live if you're not sure what you are doing. How many of us are sure what we're doing? Since you aren't using the motors any more, the current drawn by the relay won't overload the VCR's supply. Now the "Power" button on the remote will switch the VCR *and* the TV on and off. > I would like to use a PIC to control a sort of TV tuner and >remote power switch. There must be a lot of old TV's that could use a >device like this. Devices like this (called a "converter box" are still made for cable-TV tuning. There used to be some for over the air TV but they are probably hard to find now since most everyone uses cable. > >I have absolutely no idea about TV transmission. I understand that >it's >transmitted on a carrier frequency, but I will have to look up the >frequencies for my area (we use PAL standard, and I need to get VHF >and >UHF channels). Is there a world standard for the frequencies they >transmit on? TV broadcasts generally occur on frequencies between 50 and 900 MHz, but the exact frequencies are determined by politics in each country. There seems to be some agreement but it is by no means universal. >1) Filter the antenna signal for the carrier frequency of a particular >channel. > TV's and VCRs have a module called the "tuner" which does that. The tuner module is easily identified since the antenna lead goes into it. Usually the tuner is in its own metal box to shield out interference. Old-fashoined tuners are controlled by a knob, while new ones use a voltage. The low-tech way to control the voltage controlled ones is to set a voltage with little preset knobs or EEPROM settings, one for each channel. A voltage-controlled tuner can also be used as part of a PLL tuning system. Sometimes the PLL circuit is inside the tuner case, sometimes it is outside. PLL tuning is based on a synthesizer IC which accepts a binary nunber (usually through a SPI or IIC port) to select the frequency to be tuned. The set's microcontroller program includes a formula or table to generate the proper PLL control number for each channel. Also it is usually necessary to switch on and off various voltages to the tuner to select a particular "band" of channels to be tuned. Sometimes the PLL IC handles this, other times output pins from the microcontroller are used. In the case of a new tuner having a built in PLL, usually only the SPI or IIC interface and a few supply voltage are needed. In any case, the output of the tuner is a RF replica of the TV station's signal, translated in frequency to about 45 MHz. The output from the tuner is the same regardless of the frequency of the TV station. Thus, exactly the same circuit in the TV can be used to further process any channel. If you're familiar with the design of superheterodyne radio, a TV works exactly the same way. The tuner's output signal is called the "IF" signal, for Intermediate Frequency. >2) To get a 'composite' signal, which is the raw TV signal, I have to >filter out the carrier frequency. The next stage in the receiver does that. First the IF signal is amplified some and passed through a precise filter to remove any signals from TV channels that are close in frequency to the desired one (the design of the tuner doesn't reject them very well at all). Then the signal is amplified a lot more. Next a "detector" stage develops a voltage coresponding to the instantaneous amplitude of the signal. This voltage is essentially a baseband composite video signal (as would be observed at the "VIDEO OUT" RCA jack of a camera or VCR), though it also has sound information in it as well. Further processing filters the sound out of the detector signal and passes it to a sound demodulator stage. A vital support circuit controls the gain of the IF amplifiers to match the strength of the signal from the antenna. All the circuitry described in the paragraph above is usually based around one IC. Especially in VCRs, the IF and detector circuits are often integrated with the tuner and included in the tuner's case. > >3) Re-modulate this composite signal to a frequency the TV is always >tuned in to. For a converter box like you want, it isn't strictly necessary to go by your plan. Cable TV converters often do not demodulate and remodulate. Instead they convert the selected chaneel's frequency not to 45 MHz, but to a frequency of an over the air channel that any TV can receive. They skip steps 2 and 3 of your process by doing step 1 differently. Usually a double conversion is involved. It should be possible to use a stock type of tuner and convert the 45 MHz signal back up to a TV channel, using a high LO in order to invert the frequencies again. >Then comes the remote control bit. I can get an old remote control >from >a broken VCR somewhere - which will have a nice case and buttons. >Then >I have to decode the signal. Some people have posted Sony protocols >etc >but I can't be sure what protocol it will use. Does anyone know how to >capture a code from ANY control (assuming 40kHz IR type) in response >to >a button being pressed? Obtain a "universal" control sold to replace lost or broken remotes. You have a much better chance of finding a broken VCR (still suitable for your project) than the remote that goes with it. Then set the control up to send your favorite documented protocol. ___________________________________________________________________ You don't need to buy Internet access to use free Internet e-mail. Get completely free e-mail from Juno at http://www.juno.com/getjuno.html or call Juno at (800) 654-JUNO [654-5866]